Login | Register
产品中心
Home > Products > Aluminum and aluminum alloy Surface handle series > Alkali degrease agent

Alkali degrease agent

1. Application :

The product is composed of multiple components with a strong alkali corrosive fluids, can remove various oil on the surface of aluminum and natural oxide layer effectively. 


2. Parameters:     

Basicity : 25-35      

Temperature : 20-55 ℃    

Consumption : 2-3kg / Ton of aluminum  (An average thickness of aluminum is 1mm under the continues production )    Time : 3-5 minutes 


3.Tank liquid : 

With rate of 3% -5% (HA-12 and water) ,  heated to the right  temperature will done.


4. Maintenance of Bath liquid:    

Added HA—12 in accordance with the aluminum, Bath liquid should be discharged if the tank liquid too duty to had a good effect on getting rid of stain or oil . cycle of discharge is  determined by the duty of tank liquid. 


5.Storage and Notes:

Put up and down lightly, protect form heat and freezing, sealing storage, useful-life is two years. Since the product has strong corrosion , wearing anti-corrosion gloves, eye protection, wear rubber shoes, work clothes are needed when using this production.


6.Packaging :

25kg per plastic tin.



Alkali degrease agent for Aluminum Surface Treatment: Applications, Benefits, and Selection Guide

Before aluminum can be anodized, colored, polished, or prepared for another surface finish, its surface needs to be clean. Oil from machining, fingerprints, lubricants, and other residues can interfere with later treatment steps. Even when a profile looks clean to the naked eye, a thin layer of grease may remain and affect the consistency of the finished surface.

At Jianli Huaao Technology Co., Ltd., we specialize in chemical additives for aluminum profile surface treatment. We develop, produce, and supply chemicals used in different stages of aluminum finishing, and we provide technical consulting to support industrial customers. With more than 20 years of experience in this field, we understand why reliable cleaning is an important part of a well-managed production line.

Our alkali degrease agent product category is intended for alkaline cleaning applications in metal surface treatment. The right formulation can help remove oily contamination and prepare aluminum or aluminum alloy surfaces for subsequent processing. However, not every alkaline degreaser is suitable for every alloy, temperature, or production line. The exact formula, operating conditions, and compatibility requirements should always be confirmed using the product's current technical data sheet (TDS) and safety data sheet (SDS).

In this guide, we explain how an alkali degrease agent works, where it may be used, what buyers should check before purchasing, and how we approach product selection and supply. Our aim is to give production managers, purchasing teams, and surface treatment specialists practical information they can use when evaluating an aluminum degreasing chemical.

1. What Is an Alkali Degrease Agent?

An alkali degrease agent is a chemical cleaning product designed to help remove grease, oil, and other process residues from metal surfaces. It works in an alkaline environment, meaning the cleaning solution has a pH above neutral. Depending on the formulation, the product may contain alkaline builders, surfactants, and other ingredients that help loosen, disperse, or remove oily contamination.

In aluminum manufacturing, degreasing is commonly used before processes such as etching, anodizing, polishing, coating, or other surface treatments. Cleaning helps create a more consistent starting surface. It can also reduce the risk of contamination being carried into later chemical baths.

The name alkali degrease agent describes a product category rather than one universal formula. Some products are designed for aluminum profiles, while others are intended for cast aluminum, steel, or mixed-metal applications. Their working concentration, temperature, cleaning time, and material compatibility can differ. A product developed for one metal should not automatically be used on another without confirmation from the supplier.

What kinds of contamination can it remove?

Depending on its formulation and the condition of the workpiece, an alkaline degreaser may help remove:

  • Light oils and lubricants left by machining or handling.

  • Grease and oily residues from manufacturing operations.

  • Fingerprints and some forms of organic surface contamination.

  • Residues that can interfere with later surface treatment.

  • Some polishing or processing compounds, when the product is specifically designed and validated for that purpose.

Not all contaminants respond to the same cleaning chemistry. Heavy wax, hardened compounds, silicone-based residues, or specialized polishing pastes may require a different cleaning method or a dedicated product. We recommend identifying the actual contamination before choosing a degreaser rather than assuming one chemical can remove every type of residue.

Why aluminum needs careful cleaning

Aluminum is widely used because it is relatively lightweight, easy to process into many shapes, and suitable for a range of surface finishes. At the same time, its surface can react with certain chemicals. An alkaline cleaner that is too aggressive, used at an unsuitable concentration, or left on the part for too long may attack the aluminum surface or cause unwanted changes in appearance.

For this reason, choosing an aluminum alkali degrease agent involves more than checking its ability to remove oil. The product should be suitable for the alloy, surface condition, required finish, and next stage in the production line. Cleaning performance and material compatibility need to be considered together.

Where does degreasing fit in the process?

A typical aluminum surface treatment route may include degreasing, rinsing, etching or another pretreatment step, further rinsing, anodizing or coating, and final inspection. The actual sequence depends on the required product and the factory's process design.

Degreasing is often one of the first wet-process stages. If oil remains on the workpiece, it may affect how the surface responds to the next chemical treatment. If the cleaning stage is well controlled, later process steps have a more consistent surface to work with.

That said, degreasing is not a replacement for every other pretreatment operation. It does not automatically remove oxide, correct scratches, level surface roughness, or solve defects created during machining. Each stage has its own purpose, and the process should be designed around the finished product's requirements.

2. How an Alkali Degrease Agent Works

Alkaline degreasing generally works through a combination of chemical action and physical removal. The exact mechanism depends on the ingredients in the formulation. In many cleaning products, surfactants help water spread across the surface and loosen oily contamination. Other ingredients may help disperse soil in the bath, maintain cleaning conditions, or support the removal of certain types of oil.

Once the contamination is loosened, the cleaning solution and subsequent rinsing help carry it away from the workpiece. The goal is not simply to make the aluminum look clean. It is to remove the types of residues that may interfere with the next manufacturing step, while keeping the base material and required surface condition intact.

Step 1: Wetting the surface

Oil and water do not naturally mix well. A surface covered with oil can therefore be difficult for water alone to clean. Surfactants help the cleaning solution spread over the surface and improve contact between the solution and the contamination.

Good wetting is especially useful when profiles have grooves, recesses, corners, or other features that are harder to clean than a flat surface. However, part geometry, bath movement, and loading arrangements also affect whether the solution can reach all areas.

Step 2: Loosening and dispersing oil

After the cleaning solution contacts the contamination, the ingredients work to loosen and disperse it. The exact balance of chemical actions depends on the product and the type of soil. Some oils are easier to remove than others, and a product that performs well on light machining oil may not perform equally well on heavy grease or polishing wax.

This is why we recommend testing the cleaner against the real contamination found in production. A small trial using representative workpieces can help establish whether the product is suitable before a factory changes its main cleaning line.

Step 3: Removing the contamination

Cleaning may be carried out by immersion, spraying, or another process supported by the equipment and product instructions. Bath movement or spray action can help carry loosened contamination away from the surface. The appropriate method depends on the production line, part geometry, and cleaning requirements.

Concentration, temperature, and contact time also matter. A solution that is too weak may not remove the contamination effectively. A concentration or temperature that exceeds the recommended range may increase chemical consumption or create unwanted effects on the aluminum. Longer treatment is not automatically better.

Step 4: Rinsing and preparing for the next stage

After degreasing, the workpiece is usually rinsed according to the process design. Rinsing helps remove the spent cleaning solution and loosened residues. If too much cleaner is carried into the next bath, it may affect that bath's condition or create quality problems.

Rinse water quality, flow, contact time, and the arrangement of the workpieces can all influence the result. A factory should establish a rinse procedure that suits its production line and monitor it as part of routine process control.

Why temperature, concentration, and time must work together

These three factors are often central to alkaline cleaning:

  • Concentration: The amount of product in the working solution affects cleaning action and chemical consumption.

  • Temperature: Heating may improve cleaning for some formulations, but the recommended range depends on the product and aluminum material.

  • Contact time: The solution needs enough time to act, but excessive exposure may damage or alter sensitive surfaces.

We advise customers to use the operating range specified in the TDS instead of applying a general setting from another degreaser. If a factory needs to adjust the process, it should change one factor at a time where practical, record the results, and inspect the treated parts before adopting the new setting.

Comparison table 1: Main factors affecting alkaline degreasing

The table below summarizes common process considerations. It is general process guidance, not measured performance data for a specific formulation.

Process factorWhat to monitorWhy it matters
Working concentrationMake-up quantity and the supplier's recommended control methodHelps maintain cleaning performance and avoid unnecessary chemical use.
Bath temperatureActual temperature compared with the specified operating rangeTemperature can affect cleaning action and material compatibility.
Cleaning timeContact time for each batch or production cycleHelps balance contamination removal against process time and surface risk.
Bath conditionContamination level and product-specific control parametersA heavily loaded bath may behave differently from a freshly prepared one.
RinsingRinse sequence, water condition, and chemical carryoverHelps reduce the transfer of cleaner and loosened soil into later stages.
Workpiece loadingPart spacing, orientation, and solution accessSupports more consistent contact across complex profiles and components.

Source: Original process-control checklist prepared from general metal-cleaning principles. The table does not represent test results for a specific Alkali Degrease Agent. Product-specific settings should be taken from the supplier's current TDS and verified through production trials.

3. Main Benefits and Technical Considerations

When selecting an alkali degrease agent for aluminum, we suggest evaluating the whole cleaning task rather than focusing on one advertised benefit. The right product should remove the target contamination, remain compatible with the material, fit the available equipment, and support the requirements of the next process stage.

Effective removal of common oily residues

A suitable alkaline degreaser can help remove oils and grease that build up during machining, forming, handling, or other manufacturing operations. Removing these residues creates a cleaner starting point for anodizing, coating, polishing, or other finishing work.

Actual cleaning performance depends on the contamination type, its age, the substrate, and the process conditions. For example, fresh machining oil may respond differently from an old, hardened residue. Before choosing a product, describe the soil as accurately as possible and explain how it entered the production process.

Preparation for anodizing and other surface treatments

Cleaning is a key part of pretreatment for aluminum anodizing. Residual oil may interfere with the uniform response of the surface during subsequent processing. By helping remove contamination, an appropriate cleaner can support a more consistent pretreatment process.

However, the degreaser alone does not guarantee a uniform anodic coating. Alloy composition, surface condition, etching, rinsing, anodizing parameters, and later sealing or coloring stages all contribute to the final result. Quality control should therefore cover the full production route.

Compatibility with aluminum and aluminum alloys

Aluminum surfaces can be sensitive to strongly alkaline conditions. Depending on the alloy and formulation, unsuitable cleaning conditions may cause discoloration, excessive material attack, or changes in surface appearance. A product should be selected according to its intended application and used within the supplier's recommended range.

When a factory processes several aluminum alloys, we recommend checking compatibility for each important material group. A trial should include the actual parts or representative samples and should examine both cleanliness and any unwanted surface change.

Support for consistent production

A well-defined cleaning process can make production easier to manage. When operators follow written instructions and record key operating conditions, it becomes easier to identify changes in cleaning quality and compare results between shifts.

We recommend recording product identification, bath preparation, operating temperature, concentration checks, cleaning time, rinse conditions, and inspection findings where relevant. The exact record should fit the factory's quality system and the supplier's instructions.

Practical chemical use and bath maintenance

Choosing the right degreaser also involves understanding how it behaves during ongoing production. Soil gradually enters a cleaning bath, and the bath may need monitoring, replenishment, filtration, or replacement according to the product and line design.

Do not assume that adding more chemical will always restore a bath's performance. If the solution contains a high level of oil or other contamination, the underlying problem may require a maintenance action rather than additional product. Follow the supplier's instructions and the factory's chemical management procedures.

Clear technical documentation

For industrial users, the quality of the documentation is part of the buying decision. A product description should explain the intended use, while the TDS should provide the relevant operating guidance and the SDS should cover safety information.

We encourage buyers to ask questions when a recommended parameter or compatibility claim is unclear. It is better to confirm a product's suitability before a production trial than to rely on assumptions based only on a product name.

4. Applications in Aluminum Manufacturing and Other Industries

Aluminum and aluminum alloys are used in many industries because they can be shaped into different profiles and components and finished in a range of ways. An alkaline degreasing agent may be used wherever oil or grease must be removed before a compatible surface treatment. The correct product depends on the alloy, contamination, equipment, and required finish.

Aluminum extrusion and architectural profiles

Extruded aluminum profiles are used in windows, doors, curtain walls, partitions, railings, and many other building products. Before anodizing or coating, the profiles may need to be cleaned to remove handling oils, processing lubricants, or other contamination.

For architectural products, surface appearance is often important. Cleaning should be suitable for the alloy and the finish required by the customer. It should also fit the following pretreatment stages, which may include etching, desmutting, anodizing, coloring, or sealing depending on the process.

Automotive and transportation components

Aluminum is used in vehicle trim, housings, brackets, and other components. Depending on the manufacturing method, parts may carry machining oils, forming lubricants, or residues from handling. An appropriate degreasing step helps prepare the surface for later processing.

Automotive applications can have detailed quality requirements. The cleaning process should be evaluated as part of the component's complete manufacturing route, with acceptance criteria based on the drawing, customer specification, or applicable industry requirements.

Electronics and electrical equipment

Aluminum is commonly used for electronic housings, heat sinks, frames, and equipment enclosures. These parts may require anodizing, polishing, coating, or another finish. Oil residues can interfere with some subsequent operations, so cleaning chemistry should be matched to the part and the process.

Where components have tight dimensional tolerances, small features, or specific functional requirements, the trial should check both cleanliness and any possible change to the surface. The cleaning process should not be selected on oil removal alone.

Machinery and general industrial components

Machine parts and industrial equipment may accumulate cutting fluids, lubricants, and residues during fabrication. An alkaline degreaser can be considered when the material and process are compatible with the product. The cleaning method may be immersion, spray, or another approved process.

For parts with holes, channels, blind spaces, or complex shapes, solution access and drainage deserve attention. A clean outer surface does not necessarily mean that hidden areas have been cleaned effectively.

Polishing and decorative finishing

Aluminum parts prepared for polishing or decorative treatment may carry polishing compounds, oils, or waxes. These contaminants can be more difficult to remove than light machining oil. The product should be specifically suitable for the type of residue and validated under the intended process conditions.

Huaao Technology's broader product range includes polishing agents, etching agents, and other chemicals used in aluminum surface treatment. These products serve different functions, so we recommend building a process around the actual cleaning and finishing requirements rather than expecting one chemical to replace several stages.

Comparison table 2: Application needs and suggested checks

The following table is a general guide to planning a cleaning trial. It does not claim that one formulation is suitable for every application listed.

ApplicationPossible contaminationChecks to consider
Architectural aluminum profilesHandling oils and extrusion-related residuesCleanliness, appearance, alloy compatibility, and downstream finish quality
Automotive componentsMachining fluids, forming lubricants, and handling contaminationProcess compatibility and customer-defined quality checks
Electronic housings and heat sinksLight oil, fingerprints, and fabrication residuesCleanliness, dimensional requirements, and compatibility with the next stage
Machinery componentsCutting oil, grease, and production residuesCleaning of complex areas, drainage, and surface condition
Polished decorative partsPolishing compounds, wax, or oilContaminant removal and preservation of the required appearance

Source: Original application guide based on common industrial cleaning considerations. The contamination types and inspection suggestions are examples, not verified test data for a particular product. Actual suitability must be confirmed using the product documentation and application-specific trials.

5. How We Develop, Supply, and Support Surface Treatment Chemicals

At Jianli Huaao Technology Co., Ltd., our main business focuses on research and development, production, and sales of chemical additives for aluminum profile surface treatment. We also trade electroplating and magnetic raw materials and provide technical consulting. We have worked in this industry for more than 20 years.

Our company is located in the Huazhong Ecological Aluminum Demonstration Industrial Park in Jianli, Hubei, China. We serve as a standing council member of the China Non-Ferrous Metals Processing Industry Association. This industry background reflects our connection with aluminum processing, while the suitability of any specific chemical must still be determined through its technical documentation and the customer's process requirements.

A product range built around different process stages

Aluminum surface treatment is a chain of related operations. A cleaning product needs to work with the process that follows it, and the later stages must be suitable for the prepared surface. Our product range covers several of these operations, including:

  • Aluminum alloy chemical sandblasting agents.

  • Mirror polishing agents.

  • Long-life alkaline etching agents.

  • electrolytic coloring stabilizers for different colors and finishes.

  • Low-temperature, medium-temperature, and high-temperature sealing agents.

  • Bright acid etching sand surface agents.

  • Neutralization brightening agents.

  • Degreasing and dewaxing agents for aluminum alloys and cast aluminum.

  • Chromium-free passivation agents.

Because these products have different purposes, we encourage customers to explain the stage where a chemical will be used. For example, a cleaner selected for removing machining oil should not be treated as a substitute for an etching agent, and an etching agent should not be expected to perform the same role as a degreaser.

Production facilities and quality assurance

We have production facilities, testing instruments, and a quality assurance system to support our work in surface treatment chemicals. For a particular order, buyers should confirm which product documents, batch information, and inspection records are available and what will be supplied with the shipment.

For an alkali degrease agent, useful information generally includes the product identity, intended application, recommended operating conditions, bath maintenance instructions, storage requirements, and safety precautions. Where a customer has specific quality requirements, these should be discussed before a trial or commercial order.

We believe technical communication should be clear and practical. If a customer provides the aluminum alloy, contamination type, equipment, and following process, we can review the request more effectively. If a parameter needs to be confirmed, we prefer to check the applicable documentation instead of making an unsupported promise.

Lead time, inspection, and delivery

Our general production lead time is around 3–10 working days, depending on the product, order quantity, and production requirements. The actual schedule should be confirmed in the quotation or order confirmation.

Before delivery, inspection can be arranged according to the agreement between the buyer and our company. The relevant inspection items and documents should be clarified in advance so both sides understand what will be checked.

Payment terms are negotiable and may be agreed according to the order and business relationship. Delivery can be arranged through express services, logistics providers, or dedicated vehicles depending on the quantity and destination. Packaging is selected according to the product and shipping requirements, with suitable protective materials and containers used as appropriate.

For chemical products, packaging, labeling, storage, and transport must also meet the applicable safety and shipping rules. Buyers should confirm any destination-specific documentation or handling requirements before shipment.

Comparison table 3: What to confirm before placing an order

StageInformation to confirmUseful documentation
Technical evaluationAlloy, contamination type, process conditions, and intended useProduct-specific TDS and written technical confirmation where needed
Safety reviewHandling, storage, personal protection, and emergency measuresCurrent SDS and relevant safety instructions
Trial approvalSample parts, process settings, inspection methods, and acceptance criteriaTrial records and agreed inspection results
Commercial orderQuantity, price, lead time, payment, and delivery termsQuotation and confirmed purchase order
ShipmentPackaging, labeling, transport method, and required documentsShipping and inspection records as agreed

Source: Original B2B procurement checklist prepared for this product page from common industrial chemical purchasing practices. The actual documents and arrangements depend on the product, the sales agreement, and applicable regulations.

6. How to Select the Right Alkali Degrease Agent

When comparing alkaline degreasers, start with the problem you need to solve. Identify the metal, the contamination, the next process, and the quality requirements. Once these details are clear, you can compare products using the same criteria rather than relying on broad descriptions such as strong cleaning power or universal application.

Identify the metal and surface condition

Tell the supplier whether you are processing wrought aluminum, an extrusion, cast aluminum, or another metal. Explain whether the surface is machined, polished, oxidized, or already treated. These details help determine which products should be considered and which compatibility checks are needed.

If the factory processes several alloys, list the main alloy types rather than describing all parts simply as aluminum. Different materials may respond differently to alkaline conditions, so a representative trial is important.

Describe the contamination accurately

Specify whether the main problem is light oil, heavy grease, machining fluid, polishing paste, wax, or another residue. If possible, provide the name of the existing lubricant or process compound. Information about how long the contamination remains on the part can also be useful.

When the soil is unknown, start by examining the manufacturing process and collecting samples or representative parts. A cleaner should be selected for the actual contamination, not for an assumed problem.

Check the operating range and equipment

Confirm whether your line uses immersion, spray cleaning, or another method. Share the available bath temperature, tank size, circulation arrangement, cleaning time, and rinse setup. Ask the supplier whether the product is suitable for these conditions and what operating limits should be followed.

Do not change concentration, temperature, or contact time beyond the recommended range without technical review. If the existing equipment cannot maintain the required conditions, that limitation should be addressed before selecting the product.

Compare performance through a controlled trial

Before changing a production bath, agree on a trial plan. Use representative parts and define the inspection method in advance. Record the operating conditions, product consumption, cleaning results, and any unwanted surface change.

Where practical, compare the candidate cleaner with the current process under similar conditions. Avoid changing multiple variables at once, because that makes it difficult to identify what caused a difference in performance.

Consider total cost, not only purchase price

The cost of an alkaline degreaser may include the initial product price, working-solution preparation, replenishment, bath maintenance, waste handling, and the consequences of poor cleaning. The relative importance of these items depends on the factory's process and local operating costs.

To make a fair comparison, calculate consumption using the same production basis, such as the same number of parts or the same processed surface area. Include quality results and any changes in cycle time. Do not assume that a more concentrated product, a lower unit price, or a shorter cleaning cycle automatically produces a lower total cost.

Ask for the right technical and safety documents

Before purchasing, request the current TDS and SDS. Confirm the product's intended use, operating conditions, storage requirements, and handling instructions. If your customer requires a specific cleaning standard or a particular downstream finish, communicate that requirement to the supplier.

For ongoing industrial use, it is also helpful to confirm how the product is identified by batch, what quality records are available, and how any changes to product specifications will be communicated. These details support more consistent purchasing and production planning.

7. Frequently Asked Questions About Alkali Degrease Agent

What is an alkali degrease agent used for?

An alkali degrease agent is used to help remove oil, grease, and other compatible residues from metal surfaces. In aluminum processing, it is often used before anodizing, etching, polishing, coating, or another surface treatment. The exact application depends on the formulation and the factory's process requirements.

Can an alkaline degreaser be used on all aluminum alloys?

No product should be assumed suitable for every alloy without confirmation. Aluminum alloys and surface conditions can differ, and unsuitable alkaline conditions may affect the surface. Check the TDS and confirm compatibility with the supplier. Test representative parts before applying the product to the full production line.

What temperature should I use?

The correct temperature depends on the specific formulation and process. Follow the operating range stated in the current TDS. Avoid using a temperature copied from another product because its chemistry and material compatibility may be different.

How long should aluminum remain in the degreasing bath?

Cleaning time depends on the type of oil, the condition of the contamination, the product concentration, temperature, and cleaning method. Use the supplier's recommended range and verify the result with an agreed inspection method. Longer treatment is not always better, especially when the material or finish is sensitive to alkaline conditions.

Does degreasing replace etching?

No. Degreasing and etching serve different purposes. Degreasing mainly targets oil and other compatible contamination, while etching changes the surface through chemical action. Some production routes use both stages, but the correct sequence depends on the desired finish and the process design.

Can one degreaser remove oil, wax, and polishing paste?

Not necessarily. Different contaminants have different properties. Some formulations are designed for particular oils or processing residues, while waxes and polishing compounds may need a dedicated cleaner. Identify the actual contamination and confirm the product's suitability before use.

How can I tell whether the aluminum surface is clean?

The inspection method depends on the production requirements. A visual check may identify obvious residues, but it cannot always confirm that the surface is ready for the next process. A factory may use a suitable cleanliness test, process-specific inspection, or a downstream trial to evaluate the result. The acceptance method should be agreed before the trial begins.

What should I do if the surface changes color after cleaning?

Review the product concentration, temperature, treatment time, alloy, bath condition, and rinse procedure. Check whether the chemical is approved for the material and finish. If the problem continues, stop the trial when appropriate, consult the supplier, and evaluate representative parts before changing the process further.

How should the cleaning bath be maintained?

Follow the product-specific instructions for bath monitoring, replenishment, filtration, and replacement. The correct maintenance method depends on the formulation and the amount and type of contamination entering the bath. Do not rely only on visual appearance or add extra product without checking the relevant control parameters.

What documents should I request before purchasing?

Request the current TDS and SDS, confirm the product identity and intended application, and review the recommended operating conditions. Depending on your quality system, you may also need batch information, inspection records, or other agreed documents. Make sure the documents match the product and grade being supplied.

What is your usual lead time?

Our general production lead time is approximately 3–10 working days, depending on the product, quantity, and production schedule. The confirmed lead time should be agreed in the quotation or order confirmation. Transport time depends on the destination and selected delivery method.

Can you support bulk orders and repeat supply?

We can discuss product requirements, order quantities, packaging, delivery schedules, and repeat-order arrangements with industrial customers. The suitable plan depends on the specific product and demand. Share your expected consumption, destination, and required schedule so that the details can be reviewed.

Choose an Alkali Degrease Agent That Fits Your Production Line

Good aluminum surface treatment starts with a suitable cleaning process. An alkali degrease agent can help remove oils and compatible residues before anodizing, etching, polishing, or coating, but the best result depends on choosing the right formulation and controlling the process correctly.

At Jianli Huaao Technology Co., Ltd., we specialize in chemical additives for aluminum profile surface treatment and bring more than 20 years of industry experience to our work. Our product range covers degreasing and dewaxing agents, etching and polishing chemicals, electrolytic coloring stabilizers, sealing agents, and other products used in aluminum finishing.

If you are looking for an alkali degrease agent for aluminum, an alkaline degreasing chemical for aluminum profiles, or a suitable cleaner for an existing surface treatment line, we invite you to share your material, contamination type, process conditions, and quality requirements. These details help us review the application and discuss the next steps, including product documentation, trial evaluation, quotation, and delivery.

Contact Jianli Huaao Technology Co., Ltd. to discuss your aluminum degreasing and surface treatment chemical needs. Before introducing any new chemical into production, confirm the product-specific operating instructions, safety requirements, and material compatibility.

ONLINE MESSAGE

Please fill in a valid email address
Captcha Can not be empty

RELATED PRODUCTS

chat

Online Customer Service

×

This website uses cookies to ensure you get the best experience on our website.

Accept Reject