Login | Register
产品中心
Home > Products > Aluminum and aluminum alloy casting series auxiliaries > Covering flux

Covering flux

1.Performance features:

It can form a layer of dense film on the surface of aluminum liquid to reduce burning of alumium.After smelting, spread the Covering flux on cleaning liquid can precent aluminum liquid from aspirating and mingling again.


2.Use method: 

1) When aluminum ingot has been melted and flattened, spread with covering flux to reduce aluminum burning.

2) After refining of aluminum liquid, skim slay once again, the spread the required covering flux on the surface of aluminum liquid with iron shove.


3.Technical parameters:

1) Volume of 0.5~1.5kg per square meter of furnace surface area.

2) Use temperature: 700~740°C


4.Main Technical indexes:

Moisture<1.0%,Grains size-18mesh.


5.Packaging and storage:

It is 2kg for each package and 20kg for each box, which shall be stored in a dry and ventilated place. The storage period is one year if plastic bag are not damaged. It can be further used when it is ground into powder and dried under the temperature of 100ºC.



<span style="font-size: 16px;"><a href='https://www.huaaochemtech.com/tag/covering-flux' target='_blank' class='key-tag'><font><strong>Covering flux</strong></font></a> for Aluminum Melt Protection | Huaao</span>

At Jianli Huaao Technology Co., Ltd., we offer covering flux selection and supply for aluminum and aluminum alloy casting operations. We focus on a straightforward job: helping you protect the melt surface while keeping the treatment compatible with your alloy, furnace, and production routine.

When aluminum stays hot between melting and pouring, its exposed surface needs attention. Charging, sampling, and metal transfer can disturb that surface again and again. We select an Aluminum Covering Flux around those working conditions, so the material fits the way your foundry actually runs.

Our casting additive selection considers process compatibility and batch consistency. We confirm the selected product's technical requirements, quantity, and packaging before supply, with COA and SDS documentation available as agreed.

Why We Start with the Surface of Your Melt

We describe covering flux as a protective treatment for the top of molten aluminum. Its central purpose is to create a suitable barrier between the metal surface and the surrounding atmosphere. This helps limit further oxidation while the melt is being held or processed.

We pay attention to oxidation because it changes the material you eventually skim from the furnace. Dross is a mixture that can include oxides, trapped aluminum, and treatment residues. When metal leaves with that mixture, the loss matters to both production and purchasing.

Our aim is to help you manage that surface with a product suited to your operating conditions. We do not judge the treatment by whether the top of the furnace simply looks cleaner. We want to understand how the cover behaves during the full holding period and what happens when it is time to skim.

For example, a crucible opened occasionally for pouring has different needs from a holding furnace accessed throughout the shift. We ask about door openings, charging frequency, exposed surface area, and the time between treatments. Those everyday details often explain why a product performs differently from one plant to another.

We also ask what problem brought you to the page. If you are investigating excess dross, the trial should track dross and metal recovery. If you need more stable surface coverage, we should observe cover continuity over time. If your main issue is dissolved hydrogen, we need to discuss degassing as well.

We use the terms covering flux for aluminum, aluminum melt covering agent, and protective flux for molten aluminum for this application. The name identifies the intended job; the agreed product specification establishes what you receive and how it should be used.

How We Explain Covering, Cleaning, and Drossing

We keep the explanation simple: a suitable covering flux forms a protective layer at the melt surface under its intended operating conditions. Many conventional products use salt blends for this purpose. The blend needs to behave correctly at the temperature where your aluminum is actually held.

We base this general explanation on Pyrotek's treatment-flux literature, which describes covering fluxes as forming a molten salt barrier between aluminum and air. The important point for your operators is continuity. A cover with large exposed gaps cannot protect those uncovered areas in the same way.

We therefore look at how the selected material spreads, how long the layer remains useful, and how routine furnace work disturbs it. A product that works well during a quiet laboratory hold may need a different application practice on a busy production furnace.

We distinguish covering from cleaning. A cleaning flux is selected to help collect or remove unwanted nonmetallic material from the melt. A covering flux is selected primarily for surface protection. Some formulations combine functions, but we confirm those functions for the actual grade instead of assuming that every flux does everything.

We also distinguish covering from drossing. Drossing treatments help separate trapped aluminum from the dross mixture so that skimming can be more effective. Foseco's melt-treatment literature describes products that combine covering and drossing action. We use that as an industry example, not as a performance certificate for our own material.

We keep degassing separate too. Protecting a melt against further exposure is different from removing hydrogen already dissolved in it. We would review your existing degassing practice and quality checks before proposing any change to the treatment sequence.

We do not describe covering flux as a grain refiner or a general-purpose fluidity additive. If you need a finer aluminum grain structure, silicon modification, or a change in mold filling, we discuss those requirements directly. Clear treatment roles make it easier to choose the right product and investigate the result.

Our practical goal is a treatment plan your team can explain: why the product is being added, what it should do at that stage, and which measurement will show whether it is helping.

How We Match Covering Flux to Your Alloy and Furnace

We start with the alloy designation, a recent melt analysis, and your normal temperature range. The alloy name helps narrow the discussion, while the actual chemistry matters when you process returns or mixed charge materials.

We ask about sodium restrictions, magnesium content, and any element limits in your specification. Fluxes with different chemistries are not automatically interchangeable. We confirm compatibility with the chosen alloy and with other treatment products already used on the line.

We then look at temperature. The material must suit the operating range, including the cooler conditions that may occur during charging or extended holding. We do not confuse a published application temperature with the flux's own melting point; they describe different things.

The following manufacturer data show why grade selection matters. These are external examples from a published drossing and covering range. We include them to compare operating windows, not to present them as Huaao products or equivalent formulations.

Table 1. Published operating ranges for selected Nikkin drossing and covering fluxes
External reference gradePublished application temperaturePublished addition relative to melt weightEquivalent quantity per 1,000 kg melt
N118630–690°C0.1–0.4%1–4 kg
N115660–750°C0.1–0.5%1–5 kg
N115S700–800°C0.1–0.5%1–5 kg

Source: Nippon Metal Chemical Co., Ltd., official Nikkin Flux product listing, drossing/covering treatment section. We calculated the kilogram equivalents from the published percentages. The listed temperatures and additions apply to those reference products; they are not operating instructions for Huaao covering flux.

We also consider the furnace type and application equipment. A manual surface addition, a feeder, and a treatment station may require different product forms and instructions. We confirm the available form for your order instead of assuming that a powder and a granular grade can be substituted without review.

For covering flux for aluminum holding furnaces, we discuss the holding cycle in some detail. Melt weight alone does not describe surface exposure. We also need to understand the bath area, access pattern, and whether the cover must be restored during the run.

We use this information to agree a candidate grade and evaluation conditions. That gives your team a clear basis for selection before routine consumption becomes part of the production cost.

The Practical Benefits We Look for on Your Line

Surface protection that lasts through the working cycle

We look for useful coverage during the period that matters to your plant. An acceptable result immediately after application is only one observation. We also want to know what the surface looks like after sampling, charging, or a normal interval of holding.

We discuss how your operators recognize a disrupted cover and when the approved procedure calls for attention. A treatment is easier to control when those decisions are visible and consistent between shifts.

A clearer view of metal loss

We help frame the evaluation around metal accounting. Dross weight on its own can be misleading because the skim may contain different amounts of salt, oxide, and recoverable aluminum. We want the comparison to reflect your real process rather than one convenient number.

Where lower metal loss is the target, we discuss how your plant measures it and which records are reliable. We do not attach a recovery percentage to our covering flux without supporting results from defined conditions.

Handling that fits your operators and equipment

We consider pack size, identification, weighing, and the application method. Your team should be able to use the material without guesswork about the grade or quantity. We also discuss whether the packaging suits your normal consumption and storage arrangements.

We evaluate dust, fumes, and residue behavior for the selected formulation and process. Labels such as low-dust, low-fume, sodium-free, or fluoride-free need product-specific support. We confirm any required limit or declaration before including it in the supply specification.

Repeat orders with clear requirements

We focus on batch consistency through agreed technical indicators and acceptance requirements. If your approval depends on a particular test, we need that method defined. This helps production and purchasing make the same decision when a new batch arrives.

We see value in a covering flux that works within a stable routine: the correct material, an understood application, and a result your team can check.

How We Plan Application and a Fair Production Trial

We recommend a controlled evaluation before routine use. The selected product's technical instructions and your plant procedures determine the actual addition method, temperature, timing, and handling requirements. We use the trial to verify that those conditions fit your furnace.

Record the starting conditions

We begin with the alloy, charge mix, melt weight, bath temperature, exposed area, and holding duration. We record your current flux consumption and treatment sequence as well. Without that baseline, a change in charge quality can easily be mistaken for a product effect.

We also agree what will stay comparable. Furnace access, sampling, skimming, and pouring patterns all influence the observation. We would rather compare several representative heats than rely on an unusually quiet or unusually difficult run.

Calculate the quantity from the agreed basis

We make the calculation basis explicit. If the selected instruction expresses addition as a percentage of melt weight, we convert that percentage into a weighed quantity. If it uses surface area, we use that basis instead. We do not treat the two methods as interchangeable.

Table 2. Calculated flux quantities at illustrative weight-based addition rates
Melt weightAt 0.1% additionAt 0.3% additionAt 0.5% addition
500 kg0.5 kg1.5 kg2.5 kg
1,000 kg1.0 kg3.0 kg5.0 kg
2,000 kg2.0 kg6.0 kg10.0 kg

Source: our arithmetic using flux mass = melt mass × addition percentage ÷ 100. The example rates fall within the published N115 reference range in Table 1. These calculations compare material quantities only; they do not establish the correct dose, performance, or suitability of any Huaao product.

We also record any later additions separately. A starting dose and repeated top-ups are different parts of consumption. Keeping them visible makes it easier to understand why one shift uses more material than another.

Observe coverage and the next production steps

We note how the cover develops and behaves through the agreed holding period. Where practical, consistent observation times and photographs help your team compare heats. We record any change in the furnace routine alongside those observations.

We review skimming and transfer as part of the trial. Surface protection is only useful if the next steps preserve melt quality. Your approved procedure should address removal of residues and control of carryover before casting.

Check quality and total treatment cost

We compare the results relevant to your target, such as consumption per tonne, metal recovery, melt cleanliness, or a defined casting inspection. We keep the test method consistent and avoid using surface appearance as the sole proof of internal quality.

For purchasing, we calculate cost per tonne treated from delivered price and actual consumption. We can then discuss handling time and any documented change in yield. A lower bag price is useful only when the full treatment result meets your requirements.

Where We Discuss Covering Flux Applications

Automotive aluminum casting

We discuss covering flux for automotive foundries producing housings, brackets, and other aluminum components. We begin with the alloy and casting route, then review where surface protection fits between melting, holding, and pouring. The part's acceptance requirements guide the evaluation.

We keep melt-treatment claims separate from final-part approval. Covering flux is one process input; it does not establish compliance with an automotive customer's drawing or material specification.

Machinery and general foundry work

For machinery castings, we consider furnace scheduling, section sizes, and the use of internal returns. A plant handling several alloys may need separate approved flux instructions. We help clarify the material selection so an operator does not carry one treatment practice across every job.

Electrical and electronic castings

For electrical enclosures and electronic equipment housings, we discuss alloy chemistry, melt cleanliness, and any downstream finishing requirements. If a controlled property is sensitive to unwanted elements, we include that restriction in the product review.

We do not assume that a covering flux suitable for a general housing is suitable for every electrical application. The actual material specification decides what must be checked.

Aluminum recycling and remelting

We discuss aluminum remelting flux selection around the feedstock. Clean internal returns, small scrap, and fine turnings do not present the same treatment conditions. Pyrotek's literature distinguishes chip-melting fluxes from ordinary covering products, which is a useful reminder to define the job carefully.

When a buyer asks for covering flux for aluminum recycling, we therefore ask about scrap size, cleanliness, preparation, and furnace practice. We confirm whether the requirement is surface protection, scrap reclamation, combined treatment, or a different flux function.

Across these industries, we use the application name to begin the discussion. We use the alloy, equipment, and quality target to make the selection meaningful.

Why Work with Huaao on Product Selection and Supply?

We are Jianli Huaao Technology Co., Ltd., a technology-oriented enterprise engaged in chemical additive research, production, sales, and technical consulting. We have served the aluminum profile surface treatment industry for more than two decades.

We are based in the Huazhong Ecological Aluminum Demonstration Industrial Park in Jianli, Hubei, China. We serve as a standing council member of the China Non-Ferrous Metals Processing Industry Association. Our company supports its work with production facilities, precision testing instruments, and a quality assurance system.

Our broader product experience covers aluminum pretreatment, polishing, alkaline etching, acid etching, electrolytic coloring, sealing, degreasing, and chromium-free passivation additives. We bring a process-focused approach to customer discussions while keeping each product's application requirements specific.

For covering flux, we start by agreeing what the selected material needs to do in your operation. We then confirm the technical indicators and documents needed for approval. We do not use our experience in surface treatment as a substitute for checking a casting additive under its intended conditions.

Specifications and documentation

We supply according to the technical indicators, quantity, and packaging standards agreed in the contract. COA and SDS documents can be provided as required. If your receiving inspection needs a particular measurement, test method, or declaration, include it in the inquiry so we can confirm the document scope.

Packaging, lead time, and transport

We discuss suitable bag or drum packaging according to the product and order requirements. The agreed pack should support identification, storage, and handling at your site. We confirm production and preparation time against product type, stock availability, and order quantity.

We arrange the transport approach according to cargo properties and destination. Options may include sea freight, road transport, or eligible air freight. Where dangerous-goods requirements apply, the packaging and shipment must meet the relevant rules.

Commercial terms that match the order

We can discuss T/T or letter-of-credit payment terms. We also confirm the delivery schedule and documentation requirements before committing to the order. A clear technical and commercial agreement makes receiving and production planning easier for both sides.

To request a covering flux quotation, send us your alloy grade, furnace type, operating temperature, approximate melt quantity, monthly consumption, and destination. Add your current specification or treatment concern, and we can address the actual requirement rather than quote against a product name alone.

Covering Flux Questions We Address Before Supply

What is the main purpose of covering flux?

We use covering flux primarily to help protect the surface of molten aluminum against further oxidation. Some grades also provide cleaning or drossing action. We confirm the intended functions for the selected material and agree how you will assess them in production.

Can we use the same product for every aluminum alloy?

We do not assume universal compatibility. Alloy chemistry, element restrictions, temperature, and other melt treatments all matter. We review those conditions before recommending a grade, especially where sodium restrictions or magnesium-containing alloys affect product selection.

How much covering flux should we add?

We determine the application quantity from the selected product's instructions and your process. Melt mass, surface area, holding time, and furnace activity can affect the evaluation. Table 2 is a calculation example, not a universal dosage recommendation.

What temperature should we use?

We confirm the working range for the actual grade supplied. Published temperatures for another manufacturer's product cannot establish that range. We also review your normal temperature variation so the trial reflects charging and holding conditions, not just one furnace reading.

Will covering flux remove hydrogen?

We distinguish surface protection from removal of dissolved hydrogen. A cover can form part of a broader melt-control routine, but we do not promise that it replaces degassing. We retain the relevant hydrogen or melt-quality checks when evaluating the complete process.

Is powder or granular covering flux better?

We compare the available forms against your application equipment, handling needs, and target result. Form alone does not establish suitability. We confirm the actual product characteristics and instructions before approving a substitution or changing the addition method.

Can you guarantee lower dross or a specific recovery increase?

We can discuss measurable targets and a fair comparison. We do not publish a universal reduction percentage without defined test conditions. We also distinguish total dross weight from the amount of recoverable aluminum it contains.

How should we store and handle the product?

We base storage and handling guidance on the supplied formulation's SDS and packaging instructions. Keep the material identified and protected as specified. Your plant's approved procedures must control moisture exposure, application equipment, ventilation, and contact with molten metal.

What should we send for a quotation?

We need your alloy, furnace, temperature range, treatment purpose, and expected quantity. Your destination, packaging preference, and required documents help us prepare the supply discussion. A recent analysis or current product specification is useful when compatibility is a deciding factor.

Talk with Huaao about your covering flux requirements. We will help clarify the product specification, application conditions, and supply terms for your aluminum melting and holding operation.

ONLINE MESSAGE

Please fill in a valid email address
Captcha Can not be empty

RELATED PRODUCTS

No search results found!
chat

Online Customer Service

×

This website uses cookies to ensure you get the best experience on our website.

Accept Reject